Hydraulic Hose

Hydraulic Hose | Industrial Fluid Power Solutions

 

 

Qianli Rubber hydraulic hoses (Qianli Rubber - qianlirubber.com) are engineered for high-pressure fluid power transmission in mobile machinery, agricultural equipment, and industrial hydraulic systems. Built with synthetic oil-resistant NBR inner tubes, multiple layers of high-tensile steel wire reinforcement (braided or spiraled), and ozone/abrasion-resistant outer covers, these conduits maintain structural integrity under continuous pressure impulses and mechanical flexing.

 

 
First 1234 Last 1/4
 
Key Features & Benefits

Impulse Fatigue Resistance

Inner tube compound and wire adhesion layers withstand high-frequency pressure surges (exceeding standard SAE 100 impulse cycle requirements), preventing premature micro-cracking and fluid leaks.

Wide Fluid Compatibility

NBR/CR compound inner layers resist petroleum-based hydraulic oils, synthetic ester fluids, water-glycol mixtures, and biodegradable vegetable oils.

 

Abrasion & Ozone Resistant Cover

Synthetic rubber covers withstand direct friction against machine frames and prolonged ultraviolet (UV) exposure.

Consistent Dimensional Tolerance

Strict extrusion and braiding controls ensure uniform ID/OD concentricity, preventing fitting slippage and uneven crimping pressures.

 

Technical Specifications

 

Note: Custom dash sizes, specialized high-temperature fluoroelastomer (FKM) inner linings, and textile braided low-pressure lines are available upon request.

 

Hose Type

Standard Equivalent

Dash Size

ID (mm)

Max Working Pressure (MPa / psi)

Min Burst Pressure (MPa / psi)

Min Bend Radius (mm)

Operating Temp Range (°C)

QL-R1AT

SAE 100 R1AT / DIN EN 853 1SN

-04 to -32

6.3 to 50.8

22.5 / 3260 (for 1/4") to 4.0 / 580 (for 2")

90.0 / 13050 to 16.0 / 2320

100 to 630

-40°C to +100°C (120°C peak)

QL-R2AT

SAE 100 R2AT / DIN EN 853 2SN

-04 to -32

6.3 to 50.8

41.5 / 6000 (for 1/4") to 16.5 / 2390 (for 2")

165.0 / 23900 to 66.0 / 9560

100 to 630

-40°C to +100°C (120°C peak)

QL-4SP

DIN EN 856 4SP

-06 to -32

9.5 to 50.8

45.0 / 6525 (for 3/8") to 16.5 / 2390 (for 2")

180.0 / 26100 to 64.0 / 9280

180 to 850

-40°C to +100°C (120°C peak)

QL-4SH

DIN EN 856 4SH

-12 to -32

19.0 to 50.8

42.0 / 6090 (for 3/4") to 25.0 / 3625 (for 2")

168.0 / 24360 to 100.0 / 14500

240 to 1000

-40°C to +100°C (120°C peak)

 

Applications
 

Construction & Earthmoving Machinery

Excavator boom lines, wheel loader lift cylinders, backhoe steering circuits, and bulldozer hydraulic drives.

Agricultural Equipment

Combine harvester hydraulic headers, tractor auxiliary spool valve hookups, and sprayer pump lines.

Industrial Manufacturing

Injection molding clamping units, metal stamping hydraulic presses, and automated material handling lifts.

Oilfield Equipment

Mud pump return lines, blowout preventer (BOP) control systems, and mobile crane winch circuits.

 

Product Selection Guide

 

Evaluating operational parameters using the STAMP methodology ensures correct hose selection:

 

S - Size: Determine the required Inner Diameter (ID) based on flow rate velocity limits (recommended fluid velocity: 3 to 6 m/s for pressure lines) to prevent excessive pressure drop and heat generation.

 

T - Temperature: Verify both fluid temperature and ambient external temperature. Exceeding maximum thresholds hardens the inner tube and accelerates rubber degradation.

 

A - Application: Identify mechanical factors such as external abrasion, routing twists, vibration frequency, and pulling tension. Use spiral hoses (4SP/4SH) for high-pressure impulse applications; use wire-braided hoses (R1AT/R2AT) for standard mobile machinery.

 

M - Media: Check fluid chemical makeup. Standard NBR suits petroleum oils; synthetic ester or fire-resistant fluids may require specialized EPDM or FKM compounds.

 

P - Pressure: Ensure the maximum system working pressure, including pressure spikes, does not exceed the hose's rated Working Pressure (WP). The system peak pressure must remain safely below the hose's 4:1 safety factor threshold.

SAE 100R7 Thermoplastic High Pressure Hydraulic Hose

 

 
 
OEM Services
01.

Custom Lengths & Assembly

Complete hose assembly services with crimped carbon steel or stainless steel fittings (NPT, JIC, ORFS, BSP, SAE flanges).

02.

Private Labeling & Branding

Customized reel tape printing, outer cover embossing, and barcode tagging for distributors.

03.

Tailored Packaging

Wooden crating, coil bundling, or custom carton packaging to match automated warehouse receiving specs.

04.

Prototyping & Sampling

Rapid sample production for OEM design validation and burst testing.

 

Quality Control & Testing

 

Every production batch undergoes strict physical and chemical testing before warehouse dispatch:

 

Impulse Testing: Samples tested on hydraulic impulse test benches operating at 133% of working pressure at +100°C to verify cycle life.

 

Hydrostatic Pressure Testing: 100% inline proof testing applied at 2x working pressure for 30 to 60 seconds.

 

Adhesion Testing: Tensile pull testing on laboratory dynamometers to measure bonding strength between rubber layers and steel wire reinforcement.

 

Raw Material Verification: Mooney viscosity testing for rubber compounds and tensile/torsion testing for high-tensile steel wire.

 

Dimensional Inspection: Laser micrometer measurement checking ID, OD, and concentricity across entire production runs.

SAE 100R8 Thermoplastic Hydraulic Hose

 

 

Frequently Asked Questions

 

Q: What is the standard safety factor for your hydraulic hoses?

A: Our standard industrial and mobile hydraulic hoses maintain a 4:1 burst-to-working pressure safety factor (e.g., a hose with a 4000 psi working pressure has a minimum burst pressure of 16000 psi) in compliance with SAE J517 standards.

Q: Can your hydraulic hoses handle biodegradable hydraulic oils (HEES/HEPG)?

A: Standard NBR inner tubes handle traditional petroleum-based oils. For synthetic ester or polyalkylene glycol (PAG) biodegradable fluids, we recommend specifying our nitrile-blend or specialized compound variants to prevent inner tube softening.

Q: Do you supply pre-assembled hoses with end fittings, or only loose hose reels?

A: We supply both. Clients can source bulk hose on wooden reels (typically 50m to 100m coils) or request fully fabricated assemblies equipped with matched hydraulic fittings, protective spring guards, and pressure-tested crimp seals.

Q: What international manufacturing standards do your hydraulic hoses meet?

A: Our products comply with SAE J517 (Society of Automotive Engineers), DIN EN 853 / EN 856 (Deutsches Institut für Normung), and ISO 1436 standards, backed by ISO 9001 factory quality management certification.

Q: What is your standard production lead time for bulk OEM orders?

A: Standard production lead time ranges from 15 to 25 days depending on order volume, raw material availability, and custom fitting specifications. Expedited production schedules can be arranged for recurring contract orders.

 

modular-1
Request a Quote (RFQ)

Submit your specifications below to receive a formal quotation, technical data sheets, and sample pricing within 24 hours.
Required Information: Hose Type / Dash Size / Quantity (meters or assemblies) / Working Pressure Requirements / Target Port Fittings (if assemblies needed).

As one of the most professional hydraulic hose manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy bulk durable hydraulic hose made in China here from our factory.

(0/10)

clearall